MCP7H50-H002R26 Compatible 200G QSFP56 to 2x100G QSFP56 Breakout DAC Cable - 2M | Mellanox / NVIDIA
Warranty: Lifetime
200G QSFP56 to 2x100G QSFP56 Passive Breakout DAC Cable — Pre-Tested for Mellanox / NVIDIA
The MCP7H50-H002R26 is a 200G QSFP56 to 2x100G QSFP56 passive breakout DAC cable engineered for high-density spine-leaf networks, AI/HPC clusters, and hyperscale data centers. At 2 meters, it gives you the extra reach for cross-rack and mid-rack connections without stepping up to active optics. Every unit is pre-programmed with EEPROM compatibility data and validated before shipment — so it works the moment you plug it in.
Will This Cable Work With My Switch?
This cable is pre-coded for seamless plug-and-play recognition on:
- Mellanox / NVIDIA Spectrum switches (SN2700, SN3800, SN4600 series)
- NVIDIA Quantum InfiniBand platforms (HDR InfiniBand 200Gb/s)
- Any MSA-compliant QSFP56 port supporting 200GbE or HDR InfiniBand
Not sure about your exact switch model? Contact us before you buy — we'll confirm compatibility for free.
1M vs 2M — Which Length Do You Need?
| Use Case | 1M Cable | 2M Cable (This) |
|---|---|---|
| Intra-rack (same rack unit) | ✅ Ideal | Usable |
| Top-of-rack to adjacent device | May be tight | ✅ Ideal |
| Cross-rack / mid-rack runs | Too short | ✅ Ideal |
| Cable management flexibility | Minimal slack | ✅ Better slack |
Rule of thumb: if you're unsure, go 2M — you can always route extra cable, but you can't stretch a short one.
DAC vs AOC vs Transceivers — Which Should You Use?
| Feature | DAC (This Cable) | AOC | Transceivers |
|---|---|---|---|
| Cost | ✅ Lowest | Medium | Highest |
| Latency | ✅ Ultra-low (passive) | Low | Higher |
| Power Draw | ✅ 0W (passive) | Medium | High |
| Best Distance | Up to 2 meters | Up to 100m | Long-range |
Best for: top-of-rack, cross-rack, and mid-rack breakout connections where cost, latency, and power efficiency matter.
Ideal Use Cases
- GPU cluster interconnects for AI training and inference workloads
- High-throughput storage networking (NVMe over Fabric, RDMA)
- Spine-to-leaf breakout in hyperscale and enterprise data centers
- HDR InfiniBand environments requiring 200Gb/s port splitting
- Cross-rack deployments where 1M falls short
Common Mistakes This Cable Prevents
- Buying 1M when you need reach — measure your run before ordering; 2M covers most rack-to-rack scenarios
- Overspending on optics when passive DAC is sufficient for 2-meter runs
- Compatibility failures from OEM-locked or uncoded cables
- Latency overhead introduced by active components in short-distance links
Technical Specifications
- Part Number: MCP7H50-H002R26
- Data Rate: 200Gb/s (2x100Gb/s breakout)
- Connector Type: QSFP56 to 2x QSFP56
- Cable Length: 2 Meters
- Cable Type: Passive Direct Attach Copper (DAC)
- Wire Gauge: 26AWG Twinax
- Power Consumption: Passive (0W)
- Operating Temperature: 0°C to 70°C
- Standards: QSFP56 MSA compliant
- Protocol Support: HDR InfiniBand, 200GbE
The Resilient Tec Guarantee
- ✅ Pre-programmed EEPROM — recognized immediately by compatible switches
- ✅ Compatibility-tested before every shipment
- ✅ Lifetime warranty on all cables
- ✅ Talk to a real engineer — not a chatbot
We don't just ship cables. We make sure they work in your environment.
Related Products
- 200G QSFP56 to 2x100G QSFP56 DAC Cable — 1M (MCP7H50-H001R30)
- 200G QSFP56 DAC Cables (other lengths)
- 100G QSFP28 Breakout DAC Cables
- 200G QSFP56 Active Optical Cables (AOC) for longer runs
200G QSFP56 to 2x100G QSFP56 Passive Breakout DAC Cable — Pre-Tested for Mellanox / NVIDIA
The MCP7H50-H002R26 is a 200G QSFP56 to 2x100G QSFP56 passive breakout DAC cable engineered for high-density spine-leaf networks, AI/HPC clusters, and hyperscale data centers. At 2 meters, it gives you the extra reach for cross-rack and mid-rack connections without stepping up to active optics. Every unit is pre-programmed with EEPROM compatibility data and validated before shipment — so it works the moment you plug it in.
Will This Cable Work With My Switch?
This cable is pre-coded for seamless plug-and-play recognition on:
- Mellanox / NVIDIA Spectrum switches (SN2700, SN3800, SN4600 series)
- NVIDIA Quantum InfiniBand platforms (HDR InfiniBand 200Gb/s)
- Any MSA-compliant QSFP56 port supporting 200GbE or HDR InfiniBand
Not sure about your exact switch model? Contact us before you buy — we'll confirm compatibility for free.
1M vs 2M — Which Length Do You Need?
| Use Case | 1M Cable | 2M Cable (This) |
|---|---|---|
| Intra-rack (same rack unit) | ✅ Ideal | Usable |
| Top-of-rack to adjacent device | May be tight | ✅ Ideal |
| Cross-rack / mid-rack runs | Too short | ✅ Ideal |
| Cable management flexibility | Minimal slack | ✅ Better slack |
Rule of thumb: if you're unsure, go 2M — you can always route extra cable, but you can't stretch a short one.
DAC vs AOC vs Transceivers — Which Should You Use?
| Feature | DAC (This Cable) | AOC | Transceivers |
|---|---|---|---|
| Cost | ✅ Lowest | Medium | Highest |
| Latency | ✅ Ultra-low (passive) | Low | Higher |
| Power Draw | ✅ 0W (passive) | Medium | High |
| Best Distance | Up to 2 meters | Up to 100m | Long-range |
Best for: top-of-rack, cross-rack, and mid-rack breakout connections where cost, latency, and power efficiency matter.
Ideal Use Cases
- GPU cluster interconnects for AI training and inference workloads
- High-throughput storage networking (NVMe over Fabric, RDMA)
- Spine-to-leaf breakout in hyperscale and enterprise data centers
- HDR InfiniBand environments requiring 200Gb/s port splitting
- Cross-rack deployments where 1M falls short
Common Mistakes This Cable Prevents
- Buying 1M when you need reach — measure your run before ordering; 2M covers most rack-to-rack scenarios
- Overspending on optics when passive DAC is sufficient for 2-meter runs
- Compatibility failures from OEM-locked or uncoded cables
- Latency overhead introduced by active components in short-distance links
Technical Specifications
- Part Number: MCP7H50-H002R26
- Data Rate: 200Gb/s (2x100Gb/s breakout)
- Connector Type: QSFP56 to 2x QSFP56
- Cable Length: 2 Meters
- Cable Type: Passive Direct Attach Copper (DAC)
- Wire Gauge: 26AWG Twinax
- Power Consumption: Passive (0W)
- Operating Temperature: 0°C to 70°C
- Standards: QSFP56 MSA compliant
- Protocol Support: HDR InfiniBand, 200GbE
The Resilient Tec Guarantee
- ✅ Pre-programmed EEPROM — recognized immediately by compatible switches
- ✅ Compatibility-tested before every shipment
- ✅ Lifetime warranty on all cables
- ✅ Talk to a real engineer — not a chatbot
We don't just ship cables. We make sure they work in your environment.
Related Products
- 200G QSFP56 to 2x100G QSFP56 DAC Cable — 1M (MCP7H50-H001R30)
- 200G QSFP56 DAC Cables (other lengths)
- 100G QSFP28 Breakout DAC Cables
- 200G QSFP56 Active Optical Cables (AOC) for longer runs